Analysis Of Automobile Injection Mold

- Jun 20, 2017-

In the development of the automotive industry, the demand for plastic parts is increasing, because the construction of the plastic parts of the application of plastic is very high, that is the quality of plastic parts of the development and construction of the automotive industry has a huge role in promoting, which requires plastic In the production of the need for quality assurance, and determine the quality of plastic parts is the mold, because the mold of things and make the plastic parts produced in the application process to the loss of various areas of the case is not unusual, so the production of plastic parts Mold to improve the quality of plastic parts, the purpose of efficiency for China's economic development is very helpful.


We all know that the application of the plastic parts of the car is very dependent on the same time, automotive products continue to upgrade, only to master the mold production of plastic parts of the key difficulties in order to make mold production to meet the development needs of the automotive industry.

The foundation of injection mold design

1.1 plastic product design is the key

Plastic products is definitely a key point in the design of injection molds, the design of plastic products, the requirement is nothing more than possible to make plastic products model simplified, especially the design of the depression is best not to appear in the plastic product design.


Plastic products in the design of the simple requirements is a general direction, because the plastic product design has a lot of small links, simple design is the plastic products for each refinement of the requirements, on the basis of the requirements to meet the various The basic requirements of the link, such as the design of the thick mold design, it is necessary in the evolution of the mold as much as possible to achieve uniformity of the wall thickness to avoid the uneven thickness of the uneven bit. In the stiffness and hardness also need to meet the standards, which is to ensure the quality of plastic parts of a key link.

1.2 Classification of plastic products in structural design

Plastic products on both sides of the inside and outside have to meet the stripping standard stripping slope, which is more conducive to stripping. In order to make its appearance smooth, stripping from friction and obstruction, plastic products as far as possible in the curvature and texture to do streamline and smooth. Plastic products have sharp corners, these corners are rounded, for the curvature of the plastic products on both sides of the peripheral angle, the curvature of the arc should be larger, it is necessary.

A basic requirement for forming a mold

In the strength and hardness to achieve a certain standard, or can not withstand the friction, will affect the quality of construction, the hardness requirements of the lowest can not be lower than the HRC35, very special requirements in the hardness of 50 ~ 52HRC above, after the product to make it The surface is shiny, can be achieved by polishing, and the need to polish another cavity part of the product sample can not deviate from the product requirements, and then through the management and construction technology to improve production efficiency and cost savings.

Clear number of cavities

The method of determining the number of cavities can take advantage of the total injection machine and then confirm how much the quantity is by the amount of injection and the rated clamping force of the injection machine. In the process of the number of models need to be combined with other factors to complete, such as: molding process, precision and maintenance and economy.

Recognize the fractal line and mold parting surface

The method of determining the fractal line can be determined according to the shape of the part. The function of the fractal line is nothing more than the fact that the product is divided into two parts. Divided into two parts of a fixed molding, dynamic mold is another part of the molding. To get the mold parting surface can use the fractal line, with the fractal line in the two mold around the scan can determine the mold parting surface.

4.1 Partial design considerations

Step shape surface, in the face of the step surface generally need to have 3 to 5 degrees of insertion angle, angle can not be less than 1.5 degrees. Sometimes a sub-surface will appear at the same time a number of step surface, in this case, with the same angle to the role of angle A, which makes the processing can become more simple and convenient.


Mold parting surface has a special need to pay attention to is to ensure that each of the same surface has a sealed distance, but also need to protect the effectiveness of the distance, so that the injection process can make the plastic melt is not easy outflow, seal distance This name is because of this performance and corresponding, you can lock the goods. In the creation of the parting surface, if you meet the surface or slope and the height of the steps and other large differences in the parting surface, whether it is one or more, you must set the datum plane, which can facilitate processing and measurement.

4.2 Basic principles of parting design

Shaped plastic in the mold after the need to retain on the mold, of course, this is the introduction of institutions as a prerequisite in the case, the general launch of the semi-modal institutions are dynamic mode, only a very special case of the introduction of the semi-official On the mold.


Some plastic products will be attached with metal inserts, because the insert does not have the function of shrink wrap punch, shape cavity design is usually in the dynamic mode side, if not set, then open the mold will make plastic products in the mold area, In the event of such a situation, stripping will become very difficult. In the case of coaxiality in the dynamic mode or fixed mold, if the two models on both sides of the shape, coaxial degree is difficult to guarantee its accuracy, this situation is due to manufacturing errors and assembly errors Caused by.


The locking of the mold is a certain requirement, the request must be met, in order to meet the requirements generally in the geostationary modulus mold placed plastic mold, place the direction of choice of smaller projection area, the projection area of the larger direction For lateral fractal surfaces. This can greatly reduce the locking force, in addition, the parting surface sometimes appear curved surface, when this phenomenon must be added to the positioning mechanism, the choice of the parting surface as much as possible not to affect the appearance of plastic products Of the choice of parts, if the plastic products in the shape of the line and tangent line, nor is it suitable for the choice of parting.


Select the sub-surface must choose a relatively smooth and no obvious sharp corners, so the division will not affect the quality and shape, although not absolute, but the probability is still too large. Be sure to arrange the size and number of internal mold inserts.

Previous:Analysis Development Trend Of China Mold Industry On Future Next:Home Applicances To Ensure Good Machine Performance